Sensors for Hatchery Environmental Control
Hatcheries and broodstock units work to tighter margins than almost any other part of aquaculture. Egg and larval survival depends on water temperature held within a narrow band, small incubation and first-feeding tanks can drain or overflow quickly when a valve or pump fails, and the air in the hatchery building affects water temperature, condensation and working conditions. Good hatchery environmental control means measuring water and air continuously and raising an alarm before a small change becomes a mortality event.
Stork Solutions supplies submersible temperature and level transmitters, room climate sensors for temperature, humidity and CO₂, barometric pressure and temperature transmitters, and remote monitoring gateways for incubation rooms, hatching units and broodstock holding systems. Options include 316 stainless steel and marine bronze housings, 4…20 mA, SDI-12 and Modbus interfaces, and cellular telemetry with SMS and email alarms. See our wider range for aquaculture and aquatics.
Product Spotlight for Hatchery Environmental Control
Why Hatchery Environmental Control Matters
Eggs, larvae and conditioned broodstock have little tolerance for drift in their surroundings, and problems often start out of hours. Continuous measurement of water and air conditions allows hatchery teams to:
Hold incubation temperatures steady — submersible temperature transmitters in header tanks, incubators and holding tanks show drift early, so heating and chilling can be corrected before development rates are affected
Protect small tanks from draining or overflowing — low-range submersible level sensors track water depth in rearing tanks and sumps, where a blocked outlet or failed supply can change the level within minutes
Manage the room climate — air temperature, humidity and CO₂ in incubation and broodstock rooms influence condensation, heat load on the water and the working environment for staff
Keep a barometric reference — a local barometric pressure reading supports atmospheric monitoring, sensor calibration and aeration management
Respond quickly at night and weekends — a remote monitoring gateway logs every reading and sends SMS or email alarms, so a fault reaches the on-call team rather than waiting for the morning round
Sensors for Every Hatchery Environmental Control Application
Incubation and Broodstock Water Temperature
Water temperature is the main lever on egg development and broodstock conditioning, so the probe should stay permanently in the water and give a stable, low-drift reading. Choose the housing material to suit fresh, brackish or salt water.
STT-26 Submersible Temperature Transmitter
A PT100 class B temperature transmitter with a 2-wire 4…20 mA output, 10…30 V dc supply and IP68 protection, suspended by its cable. Housings are 316 stainless steel with PUR cable (STT-26-SP), CA104 marine bronze with TPE-U cable (STT-26-MT) or Monel alloy 400 with TPE-U cable (STT-26-NT); the marine bronze and Monel versions are offered for seawater use. A USB configuration kit is available.
STT-28 SDI-12 Submersible Temperature Transmitter
A fully submersible IP68 transmitter with an SDI-12 interface, NTC thermistor sensing corrected in low-power digital electronics, and a stainless steel or marine bronze housing. A 10 mm thin-walled probe gives a faster response for incubator water, while the standard probe suits long-term trend monitoring. Rescaling is carried out with the USB-SDI12-PRO interface and free software.
Small-Tank and Sump Level Monitoring
Incubation troughs, larval rearing tanks and header tanks hold relatively little water, so a low-range hydrostatic sensor resting near the tank floor gives a continuous level reading with no moving parts to foul. Both sensors below are built in 316 stainless steel; confirm suitability for seawater systems with Stork.
SLS-SA Submersible Level Sensor, Analogue Output
Level ranges from 0.5 mWG up to 100 mWG, with 4…20 mA (2-wire), 0…5 V or 0…10 V (3-wire), 0.5…4.5 V ratiometric or low-power millivolt outputs. Accuracy options are <±0.25%, <±0.15% and <±0.1%, using an isolated diaphragm silicon piezo-resistive sensing element with FKM, EPDM or NBR seals, PUR submersible cable and IP68 protection. An optional temperature output is available.
SLS-SD Submersible Level Sensor, Digital Output
The same 0.5…100 mWG ranges with an SDI-12 version 1.4 output that carries level and temperature as standard, so one probe reports both. Up to nine sensors can share a single bus, current draw is under 250 µA idle and under 4 mA active, and the integrated temperature sensor supports density correction. IP68 rated for permanent submersion.
Room Climate and Barometric Pressure
The air in incubation, hatching and broodstock rooms affects heat gain or loss from the water, condensation on equipment and the comfort of staff. Wall or duct mounted sensors give the building management or control system the data it needs to keep conditions stable.
FEEL Multi-parameter Sensor
A modular sensor that records up to five values, with options for temperature and humidity, CO₂, VOC and differential pressure. Temperature accuracy is ±0.3 K and humidity accuracy ±2%, with switchable analogue outputs, an optional open collector switch output, optional RS485 Modbus and an optional high-resolution TFT display. The temperature and humidity probe can be room or duct mounted.
SBPT Barometric Pressure & Temperature Transmitter
Combines a piezo-resistive silicon pressure sensor with an NTC 10 kΩ thermistor in a robust die-cast aluminium housing, giving pressure accuracy of ≤±0.25% FS BFSL and temperature accuracy of ≤±0.2 °C. A 2 m screened cable or M12 connector is available. Several pressure ranges and output signals are listed, so confirm the version that suits your control system with Stork.
Heating and Chilling Circuits, Telemetry and Alarms
Heater, chiller and heat exchanger loops need their own temperature points, and every reading is more useful when it reaches the right person at the right time. These products cover configurable temperature measurement and off-site monitoring.
TTT Titan Temperature Transmitter
Works with PT100, PT1000, NTC and PTC resistance thermometers as well as thermocouples, with 0.5…4.5 V analogue (ratiometric or regulated) or digital I2C and SPI outputs. The rugged stainless steel enclosure is rated IP66 with an integrated cable outlet or M12 x 1 4-pin connector, and probe lengths and process connections can be customised.
ECHO-IoT Remote Monitoring Gateway
Accepts four 4…20 mA or 0…10 V analogue inputs, eight volt-free digital inputs, Modbus instruments over RS-232, RS-485 or Ethernet, and up to 128 IWT wireless transmitters. Data travels over a built-in 2G/3G/4G modem using MQTT to a web-based SCADA system viewable on a computer, smartphone or tablet, with email or SMS alarms and four relay outputs. Supply is 12…36 V dc and the unit is rated IP67.
Certifications & Compliance
Approvals and protection ratings vary by model and version, so confirm the options you need on the relevant product page or with our team. The products above offer the following:
IP68 ingress protection — STT-26, STT-28, SLS-SA and SLS-SD for permanent submersion in tanks and sumps
IP67 ingress protection — ECHO-IoT remote monitoring gateway
IP66 ingress protection — TTT Titan stainless steel enclosure
SDI-12 version 1.4 compliance — SLS-SD, for multi-sensor bus networks and data loggers
WRAS-approved cable granules — used in the PUR cable of the STT-26-SP stainless steel version